Настройки

Укажите год
-

Небесная энциклопедия

Космические корабли и станции, автоматические КА и методы их проектирования, бортовые комплексы управления, системы и средства жизнеобеспечения, особенности технологии производства ракетно-космических систем

Подробнее
-

Мониторинг СМИ

Мониторинг СМИ и социальных сетей. Сканирование интернета, новостных сайтов, специализированных контентных площадок на базе мессенджеров. Гибкие настройки фильтров и первоначальных источников.

Подробнее

Форма поиска

Поддерживает ввод нескольких поисковых фраз (по одной на строку). При поиске обеспечивает поддержку морфологии русского и английского языка
Ведите корректный номера.
Ведите корректный номера.
Ведите корректный номера.
Ведите корректный номера.
Укажите год
Укажите год
Применить Всего найдено 5. Отображено 5.
09-09-1986 дата публикации

Folding machines

Номер: US0004610041A1
Автор: Yardley; Robert, Cameron; Ewen R., Wolloff; Frank H.
Принадлежит: Enhart Corporation

A folding machine has workpiece sensing means including an emitter by which an "outside" corner in the workpiece edge approaching the operating locality of the machine can be sensed, such sensing causing the feed length by which the workpiece is advanced step-by-step through the operating locality to be reduced; this conventionally causes pleating in the folded over edge portion. In addition, delay means is provided by which, after the emitter has been re-covered by the workpiece, the feed length reduction continues for a given number of further feed steps.

Подробнее
Номер записи: 1
10-12-1985 дата публикации

Automatically controlled thermo-cementing and folding machine

Номер: US0004557787A1
Автор: Mansfield; Graham J., Hall; Dennis S., Cameron; Ewen R.
Принадлежит: USM Corporation

In a thermo-cementing and folding machine, a gear pump operates to supply adhesive at a rate which is dependent upon the speed of rotation of a main drive shaft, by which workpiece feeding means of the machine is driven. The machine has also a facility for varying the rate of feed of a workpiece by the workpiece feeding means without varying the speed of rotation of the main drive shaft. The ratio of the rotational speed of the shaft to the operating rate of the pump is varied in response to variation of the workpiece feed rate. This arrangement is achieved by computer control, the gear pump being driven by a stepping motor for this purpose. In addition, at the end of each work cycle, use of a stepping motor facilitates "suck back" of adhesive, and a "fast forward" adhesive upon initiation of the next work cycle.

Подробнее
Номер записи: 2
13-05-1986 дата публикации

Adhesive supplying system

Номер: US0004588109A1
Автор: Cameron; Ewen R., Yardley; Robert, Wolloff; Frank H.
Принадлежит: USM Corporation

In a thermo-cementing and folding machine which has a suck-back facility, by which at the end of an adhesive-applying operation adhesive supplied through the nozzle (22) is sucked back into the nozzle so as to prevent `drooling`, auxiliary suck-back steps are introduced at timed intervals following the primary suck-back operation, through controlled amounts, in order to counter further risk of `drooling` caused by thermal expansion of the adhesive in the nozzle (22). The number of auxiliary suck-back steps is variable according to the adhesive supply rate at the time of termination of the adhesive-applying operation.

Подробнее
Номер записи: 3
11-02-1986 дата публикации

Control circuit for numerically controlled motor

Номер: US0004570112A1
Автор: Yardley; Robert, Cameron; Ewen R., Shutt; Joseph A., Walter; Andrew G. N.
Принадлежит: USM Corporation

A numerically controlled motor provides a drive at a rate which is proportional to rotation of an independently driven shaft. In addition, the ratio of such rate to such rotation can be varied by a control circuit by which, in response to each pulse supplied by an encoder on said shaft, an incremental value, corresponding to an analogue signal supplied by a potentiometer to an A-D converter, which converts said signal to said value, is supplied to an accumulator, which sums the successively supplied increment values and, at a predetermined cumulative value, "overflows", such "overflow" supplying a drive signal to the n.c. motor. The potentiometer is manually set by an operator to vary the increment value and thus the frequency of "overflow" in relation to shaft rotation. The control circuit also enables "reverse" and "fast forward" drive to the motor independently of the shaft.

Подробнее
Номер записи: 4
21-12-1993 дата публикации

Drive arrangement

Номер: US0005271348A1
Автор: Cameron; Ewen R., Smith; Andrew
Принадлежит: British United Shoe Machinery Ltd.

A drive arrangement comprises an a.c. induction motor (M1) having a rotary output shaft, and a drive control (FIG. 2), by which the speed of rotation of the shaft is controlled. The drive control comprises a signalling arrangement (e.g. a transducer (T) supplying an analogue signal converted by an analogue-to-digital converter (ADC) or a direct digital signalling arrangement) for supplying a digital signal having a value corresponding to the desired speed of rotation of the motor shaft, together with a processor (CPU) which receives the digital signal and at least one other input and processes the digital signal in accordance therewith. The processor supplies a corresponding, but modified, digital output signal to a digital-to-analogue converter (DAC) which converts the digital output signal to an analogue control signal and supplies it to an inverter which, in response thereto, drives the a.c. induction motor. An encoder (E) is operatively connected to the output shaft of the motor and ...

Подробнее
Номер записи: 5