Настройки

Укажите год
-

Небесная энциклопедия

Космические корабли и станции, автоматические КА и методы их проектирования, бортовые комплексы управления, системы и средства жизнеобеспечения, особенности технологии производства ракетно-космических систем

Подробнее
-

Мониторинг СМИ

Мониторинг СМИ и социальных сетей. Сканирование интернета, новостных сайтов, специализированных контентных площадок на базе мессенджеров. Гибкие настройки фильтров и первоначальных источников.

Подробнее

Форма поиска

Поддерживает ввод нескольких поисковых фраз (по одной на строку). При поиске обеспечивает поддержку морфологии русского и английского языка
Ведите корректный номера.
Ведите корректный номера.
Ведите корректный номера.
Ведите корректный номера.
Укажите год
Укажите год
Применить Всего найдено 4. Отображено 4.
20-08-1991 дата публикации

KNIFE HOLDER FOR KNIFE CARRIAGE OF SCRAP SHEAR

Номер: JP0003190616A
Автор: HERUMUUTO MANSHIYUUETOUSU
Принадлежит:

PURPOSE: To dismantle a knife in a downward direction without dismantling wearing plates on the feed channel side by removing knife securing screws, and making a sleeve slidable in the back direction of a knife carriage from a knife contact face. CONSTITUTION: In an operational state, a short sleeve 10 is brought into contact with an end face 11a aligned toward a knife 4 of a long spacer sleeve 11 held by knife securing nuts 6. The knife securing nuts 6 are loosened, knife securing screws 5, 5a are removed, then the knife 4 is dismantled toward a return path 8. The short sleeve 10 is located outside the contact face of the knife 4 by a tool introduced through the screw head opening section 19 of the knife 4 together with the long spacer sleeve 11, and the short sleeve 10 is made movable in the backward direction of a knife carriage 2 to resolve the retention of the integral coupling between the knife 4 and a knife support 9 or the knife carriage 2.

Подробнее
Номер записи: 1
30-05-1995 дата публикации

CRUSHING APPARATUS

Номер: JP0007136531A
Автор: PEETAA ZERUBAN, HERUMUUTO MANSHIYUUETOUSU, JIIGUMAARU SHIEEFUAA, YOOZEFU UEEBAA
Принадлежит:

PURPOSE: To suppress the generation of a peak value by installing positioning elements for determining load at a housing to determine the relative positions of a rotor and a crushing force receiving surface and enabling the relative motion of the rotor and the crushing force receiving surface in case of overloading. CONSTITUTION: This rotor 3 rotating about a horizontal axis 2 is pivotally supported within a housing 1 of a hammer crusher. On the other hand, hammers 5 are movably pivotally fitted on the horizontal axis 4 of the peripheral surface of the rotor 3. As the rotor 3 rotates in an arrow direction 7, the material loaded from a loading port 8 is crushed and is ejected to a discharge port 9. A bearing 10 housing the shaft 2 is, thereupon, coupled to one end of a carrier arm 11 housed in a bearing loading part 12. The other end of the carrier arm 11 is guided along the housing 1 swivelably by means of a web 13 and plural shaft journals 14 and 15. Further, both sides of the carrier ...

Подробнее
Номер записи: 2
15-03-1989 дата публикации

APPARATUS FOR SECURING CAP ON THE END OF SUPPORT FOR HAMMER-CRUSHER -ROTOR

Номер: JP0064070154A
Автор: HERUMUUTO MANSHIYUUETOUSU
Принадлежит:

PURPOSE: To remove a cap from a supporting body end and to make this cap exchangeable without disassembling a hammer shaft by interposing a packing member as a projection for shape complementary securing of the cap. CONSTITUTION: The cap 1 covers the end 2a of the supporting body 2 from all directions. Clearances 3, 3a are formed with respect to the hammer shaft 5 at a side wall 4. Both ends have nearly rectangular openings 6. The packing member 7 is inserted into a groove 2f from the flank 2d at the end of the supporting body 2 existing backward in the rotating direction of a rotor, by which the projection 2c is formed. An elastic element 12 guided into the packing member 7 holds the position of the packing member 7. At the time of disassembling the cap 1, the packing member 7 is extruded sideways against the elastic holding effect of the element 12 and thereafter, the cap 1 is oscillated forward around the edge of the projection 2b. The cap 1 is symmetrical with a plane F and is, therefore ...

Подробнее
Номер записи: 3
18-07-1991 дата публикации

SLIDE-TYPE CHARGING BOX FOR SCRAP PUSHER

Номер: JP0003166009A
Автор: HERUMUUTO MANSHIYUUETOUSU
Принадлежит:

PURPOSE: To prevent a compressed object from being pinched between a movable closure wall and the free end section of an angularly adjustable compactor wall by setting the center of curvature of the end face of the compactor wall to the rotational axis of a hinge guided by a fixed side wall, and setting the center of curvature of the side face of the closure wall to the rotational axis likewise. CONSTITUTION: An insertion box inner chamber 1b is closed by a movable- closure wall 15 on the opposite side to a fixed side wall 13 regardless of the position of an angularly adjustable compactor wall 5. The convexly curved end face 15a of the movable closure wall 15 is kept in contact with the end face 14a of a feed slider faced to it. The closure wall 15 is shape-supplementally held not to be drifted to the side by a stationary guide pin 16. The guide pin 16 is coupled with an arc-shaped groove 17 formed on the bottom of the movable closure wall 15. The center of the radius of curvature of the ...

Подробнее
Номер записи: 4